Mikroe mikromedia Plus for STM32

Product ID: 8151
Mikroe mikromedia plus for stm32 7318240860
$258.99 Backordered

Ships in 15 to 20 days

Main features

ARM® Cortex® M4 on-board.

chip.png

Once you experience 168 MHz on a microcontroller, you won’t be turning back. Mighty STM32F407ZGT6 with FPU has a breathtaking performance.

Large 4.3" Touch Screen

scale.png

It's time to see the big picture. New 4.3” touch screen driven by SSD1963 graphics controller delivers crystal sharp image in 480x272px resolution.

Communicate wirelessly.

wifi.png

Nordic’s nRF24L01+ transceiver with the Rufa 2.4GHz SMD antenna allows development of wireless applications.

A whole lot of modules

puzzl.png

Board has it all: USB connector, temp. sensor, RTC battery, PIN photosensor, IR receiver, accelerometer, battery charger, MP3 codec, buzzer, etc.

What’s on Board

Click on the desired thumbnail to view full image.

cercle_rouge.png
ir_reciever.png

Infrared Receiver

IR receiver diode enables you to remotely control your device.

rgb_led.png

RGB LED

Front side features RGB LED which is useful for simple visual signalization.

photodiode.png

Photosensor

PIN photosensor enables you to measure ambient light and respond by dimming or brightening up the screen backlight.

mounting_holes.png

Mounting Holes

Four mounting holes, one in each corner of the board, facilitate board integration.

frontal_reset.png

Reset Button

High quality reset button with surrounding reset circuitry ensures stable reset operation.

connection_pads.png

Connection pads

Every unsused microcontroller pin is available through connection pads. They can be used to connect your mikromedia board with additional shields or accessory boards.

tft.png

4.3" Touch Screen

480x272 Color TFT Display with Touch Panel can display vivid and clear color images or advanced graphic content.

temp_sensor.png

Temperature Sensor

Analog Temp. Sensor MCP9700A is used to measure temperature from -40ºC to 125ºC.

pwr_led.png

Power LED

We have added power indicator LED, so you can be sure whether your board has stable power supply.

battery_led.png

Battery Indicator LED

Whenever your board charges the battery, this LED will glow in red. When it’s fully charged it will change to green. Handy, isn’t it?

audio_jack.png

Audio connector

Quadrupole audio connector enable you to connect headphones with microphone to the audio codec chip and use it in your applications.

off_switch.png

ON/OFF Switch

Two position ON/OFF switch is a handy feature. It’s conveniently located right on the edge of the board.

mp3_codec.png

Stereo Audio codec

VS1053 MPEG audio decoder with SPI interface for fast reproduction of Ogg Vorbis / MP3 / AAC / WMA / FLAC / MIDI audio files.

jtag.png

JTAG connector

Pads for connecting and programming the board with mikroProg for Stellaris external programmer.

piezoBuzzer.png

Piezo Buzzer

With piezo buzzer you can debug your applications, or have audio signalization feature. It can be connected to two digital output pins, one of which is the output of PWM module.

solomon.png

SSD1963

Popular Solomon graphics controller SSD1963 handles the TFT display. It has built-in 1215K bytes frame buffer, Dynamic Backlight Control and many other cool features.

tft_connector.png

Touch Screen Connector

Connector for the Touchscreen flat cable is located at the back of the board.

rtc_battery.png

RTC battery

Lithium polymer battery is providided for retaining data and powering internal Real-Time Clock module of the microcontroller.

accelerometer.png

Accelerometer

On-board ADXL345 Digital Accelerometer allows you to measure acceleration.

serial_flash.png

Serial Flash Memory

Store up to 8 Mbit of data in M25P80 Serial Flash Memory with 25 MHz SPI Bus Interface. It suports over 100,000 Erase/Program Cycles per Sector and has over 20 Year Data Retention.

smsc_ethernet_phy.png

Ethernet PHY

LAN8720A provides neccessary physical layer for fast 10/100Mbps ethernet supported in STM32 microcontroller.

mcu.png

STM32F407ZGT6

High-performance STM32 ARM® Cortex™-M4 microcontoller with on-chip FPU and DSP easily handles demanding applications.

oscilltr.png

Crystal Oscillator

8Mhz crystal oscillator circuit that provides external clock is connected to microcontroller osc pins.

rtc_xtal.png

RTCC Crystal Oscillator

Board contains 32.768kHz Crystal oscillator (X1) which provides external clock for internal RTCC module.

power_screw_terminal.png

Power Terminals

You can easily provide necessary power supply using these power supply screw terminals.

battery_connector.png

Battery connector

Li-Polymer battery connector allows you easier connection with your battery. Autonomous power supply will give your mikromedia the wings it deserves.

battery_charger.png

Battery Charger circuit

MCP73832 Battery Charger circuit enables you to charge your Li-Polymer battery directly from USB port.

nordic_rf.png

RF Transceiver

Nordic nRF24L01+ is a wireless ultra low power 2.4 GHz RF transceiver. It has a standard SPI interface.

rf_antenna.png

Active RF chip antenna

Active RF chip antenna for 2.4 GHz RF transceiver.

microsd_slot.png

microSD card slot

microSD Card slot allows you to store large ammounts of data externally on microSD card using fast SDIO communication.

usb.png

miniUSB connector

Microcontroler supports Full Speed and USB 2.0 OTG, so this connector allows you to communicate with a PC or other USB devices using USB connection.

Why choose mikromedia

Programming

programming.png

On-board microcontroller is preprogrammed with fast USB HID bootloader, so it’s ready to work right out of the box. You don’t have to spend a dollar more on programmers. If you need a debugger use mikroProg for STM32.

Compilers

3d-printing-software.png

mikromedia Plus for STM32 is fully supported by mikroC, mikroBasic, mikrobasic and mikroPascal compilers for ARM. Compilers come with dozens of examples that demostrate every feature of the board.

GUI design with Visual TFT

analytics.png

Easily create fantastic colorful graphical user interfaces (GUI) for mikromedia in VisualTFT software. Even total beginners will be able to create amazing mikromedia applications.

why_choose_mikromedia.png

Modules

Click on the desired thumbnail to view full image.

Graphics Controller

mikromedia_plus_for_STM32_audio_small.pn

Popular Solomon graphics controller SSD1963 handles the TFT display. It has built-in 1215K bytes frame buffer, Dynamic Backlight Control and many other cool features.

Audio connector and codec

mikromedia_plus_for_STM32_gpu_small.png

VS1053 MPEG audio decoder with SPI interface for fast reproduction of Ogg Vorbis / MP3 / AAC / WMA / FLAC / MIDI audio files, 3.5mm four pole audio jack allows you to directly connect your headset to mirkomedia and develop various audio applications

microSD card slot

mikromedia_plus_for_STM32_mmc_small.png

microSD Card slot allows you to store large ammounts of data externally on microSD card using fast SDIO communication.

Wireless connectivity

mikromedia_plus_for_STM32_wireless_small

Mikromedia plus for STM32 is equipped with the Rufa 2.4GHz antenna, from antenova(r). It allows easy development of applications that use wireless communication.

miniUSB connector

mikromedia_plus_for_STM32_usb_small.png

Microcontroler supports Full Speed and USB 2.0 OTG, so this connector allows you to communicate with a PC or other USB devices using USB connection.

Battery connector

mikromedia_plus_for_STM32_battery_small.

Li-Polymer battery connector allows you easier connection with your battery. Autonomous power supply will give your mikromedia the wings it deserves.

What’s in the Package

All images shown are for illustration purpose only. Actual board may vary due to product enhancement.