Mikroe mikromedia Plus for FT90X

Product ID: 7822
Mikroe mikromedia plus for ft90x 5054878816
$258.99

Ships in 15 to 20 days

Main features

Fast and furious

chip.png

Fast FT900 microcontroller with 256KB of Flash, 256KB of shadow RAM, operating at 100 MHz. Execution from shadow RAM gives it 3.1 DMIPS/MHz.

Large 4.3" Touch Screen

scale.png

See the big picture. A 4.3” touch screen driven by FT810 graphics controller from FTDI delivers crystal sharp image in 480x272px resolution.

Communicate wirelessly.

wifi.png

Nordic’s nRF240L01+ transceiver with active chip antenna will make you forget about wires. Drive it with simple SPI commands. It that easy.

A whole lot of modules

puzzl.png

Board has it all: USB connector, temperature sensor, PIN photosensor, IR receiver, accelerometer, battery charger, MP3 codec, buzzer, etc.

What’s on Board

Click on the desired thumbnail to view full image.

cercle_rouge.png
rgb_led.png

RGB LED

Front side features RGB LED which is useful for simple visual signalization.

mountingholes.png

Mounting Holes

Four mounting holes, one in each corner of the board, facilitate board integration.

photodiode.png

Photosensor

PIN photosensor enables you to measure ambient light and respond by dimming or brightening up the screen backlight.

ir_reciever.png

Infrared Receiver

IR receiver diode enables you to remotely control your device.

frontal_reset.png

Reset Button

High quality reset button with surrounding reset circuitry ensures stable reset operation.

tft_new.png

4.3” Touch Screen

480x272 Color TFT Display with Touch Panel can display vivid and clear color images or advanced graphic content.

connection_pads.png

Connection pads

Every unused microcontroller pin is available through connection pads. They can be used to connect your mikromedia board with additional shields or accessory boards.

ethernet_leds.png

Ethernet Indicators LED

Two LEDs (Link and Ackowledge) are provided for monitoring ethernet communication.

temp_sensor.png

Temperature Sensor

Analog Temp. Sensor MCP9700A is used to measure temperature from -40ºC to 125ºC.

pwr_led.png

Power LED

We have added power indicator LED, so you can be sure whether your board has stable power supply.

battery_led.png

Battery Indicator LED

Whenever your board charges the battery, this LED will glow in red. When it’s fully charged it will change to green. Handy, isn’t it?

mcu.png

FT900

High-performance FT900 microcontoller with 256KB of Flash, 128KB of RAM operating at 100 MHz with 3.1 DMIPS/MHz.

mikroprog.png

mikroProg connector

Pads for connecting and programming the board with mikroProg for FT90x external programmer and debugger.

piezo_buzzer.png

mikroProg connector

Pads for connecting and programming the board with mikroProg for FT90x external programmer and debugger.

audio_jack.png

Audio connector

Quadrupole audio connector enable you to connect headphones with microphone to the audio codec chip and use it in your applications.

switch_on_off.png

ON/OFF Switch

Two position ON/OFF switch is a handy feature. It’s conveniently located right on the edge of the board.

mp3_codec.png

Stereo Audio codec

VS1053 MPEG audio decoder with SPI interface for fast reproduction of Ogg Vorbis / MP3 / AAC / WMA / FLAC / MIDI audio files.

tft_connector.png

Touch Screen Connector

Connector for the Touchscreen flat cable is located at the back of the board.

ft810.png

FT810

FT810 is an easy-to-use graphic controller with an Embedded Video Engine (EVE) from the same vendor that provides the main MCU.

port_expander.png

Port Expander

Board features MCP23S17, a 16-bit I/O expander with SPI clock speeds up to 10 MHz which provides two additional GPIO PORTS.

serial_flash.png

Serial Flash Memory

Store up to 8 Mbit of data in M25P80 Serial Flash Memory with 25 MHz SPI Bus Interface. It suports over 100,000 Erase/Program Cycles per Sector and has over 20 Year Data Retention.

accelerometer.png

Accelerometer

On-board ADXL345 Digital Accelerometer allows you to measure acceleration.

oscillator.png

Crystal Oscillator

8Mhz crystal oscillator circuit that provides external clock is connected to microcontroller osc pins.

rtc_xtal.png

RTCC Crystal Oscillator

Board contains 32.768kHz Crystal oscillator (X1) which provides external clock for internal RTCC module.

usb.png

miniUSB connector

Microcontroler supports Full Speed and USB 2.0 OTG, so this connector allows you to communicate with a PC or other USB devices using USB connection.

microsd_slot.png

microSD card slot

microSD Card slot allows you to store large ammounts of data externally on microSD card using fast SPI communication.

rf_antenna.png

Active RF chip antenna

Active RF chip antenna for 2.4 GHz RF transceiver.

nordic_rf.png

RF Transceiver

Nordic nRF24L01+ is a wireless ultra low power 2.4 GHz RF transceiver. It has a simple UART interface.

battery_charger.png

Battery Charger

MCP73832 Battery Charger circuit enables you to charge your Li-Polymer battery directly from USB port.

battery_connector.png

Battery Connector

Li-Polymer battery connector allows you easier connection with your battery. Autonomous power supply will give your mikromedia the wings it deserves.

power_screw_terminal.png

Power Terminals

You can easily provide necessary power supply using these power supply screw terminals.

Why choose mikromedia

Programming

programming.png

On-board microcontroller is preprogrammed with fast USB HID bootloader, so it’s ready to work right out of the box. You don’t have to spend a dollar more on programmers. If you need a debugger use mikroProg for FT90x.

Compilers

3d-printing-software.png

Mikromedia Plus for FT90x is fully supported by mikroC, mikroBasic, mikrobasic and mikroPascal compilers for FT90x. Compilers come with dozens of examples that demostrate every feature of the board.

GUI design with Visual TFT

analytics.png

Easily create fantastic colorful graphical user interfaces (GUI) for mikromedia in VisualTFT software. Even total beginners will be able to create amazing mikromedia applications.

mikromedia-4-ft90x-front_hands.png

Modules

Click on the desired thumbnail to view full image.

Graphics Controller

ft90x_graphics_small.png

Popular Solomon graphics controller SSD1963 handles the TFT display. It has built-in 1215K bytes frame buffer, Dynamic Backlight Control and many other cool features.

4 Audio connector and codec

ft90x_audio_small.png

VS1053 MPEG audio decoder with SPI interface for fast reproduction of Ogg Vorbis / MP3 / AAC / WMA / FLAC / MIDI audio files, 3.5mm four pole audio jack allows you to directly connect your headset to mirkomedia and develop various audio applications.

microSD card slot

ft90x_microSD_small.png

microSD Card slot allows you to store large ammounts of data externally on microSD card using fast SDIO communication.

Wireless connectivity

ft90x_wireless_small.png

Mikromedia plus for STM32 is equipped with the Rufa 2.4GHz antenna, from antenova(r). It allows easy development of applications that use wireless communication.

miniUSB connector

ft90x_miniUSB_small.png

Microcontroler supports Full Speed and USB 2.0 OTG, so this connector allows you to communicate with a PC or other USB devices using USB connection.

Battery connector

ft90x_battery_small.png

Li-Polymer battery connector allows you easier connection with your battery. Autonomous power supply will give your mikromedia the wings it deserves.

What’s in the Package

All images shown are for illustration purpose only. Actual board may vary due to product enhancement.